Warning: "continue" targeting switch is equivalent to "break". Did you mean to use "continue 2"? in /customers/8/3/e/lilliesystems.com/httpd.www/WPSite/wp-content/plugins/revslider/includes/operations.class.php on line 2252 Warning: "continue" targeting switch is equivalent to "break". Did you mean to use "continue 2"? in /customers/8/3/e/lilliesystems.com/httpd.www/WPSite/wp-content/plugins/revslider/includes/operations.class.php on line 2256 Warning: "continue" targeting switch is equivalent to "break". Did you mean to use "continue 2"? in /customers/8/3/e/lilliesystems.com/httpd.www/WPSite/wp-content/plugins/revslider/includes/output.class.php on line 2903 Products - Lillie Systems

Products overview

6 DOF Inertial measurement unit with CAN Bus

NEW A2C-IMU Inertial measurement unit (IMU) with IP69 rating and fastest data rate for its class.

Strain gauge amplifier with CAN bus

NEW A2C-SG2 with IP67 rating and faster data rate. 2 channel strain gauge amplifier with CAN bus interface. Convert mV inputs to CAN bus and analyze up to 2 channels. Channels can be connected together so the difference / addition / multiplication or ratio of different channels can be analyzed. 6 alarms setting and a logic (automotive compliant) output enables stand alone operation.

Acceleration / Angle with CAN bus

This new Acceleration / Angle sensor can work as a standalone sensor with logic alarm output or connected to your host controller. Available with M12 connector or in a smaller housing with cable.

A2C-mA

4-20mA Analyzer with 3 channels. Convert mA inputs to CAN bus and analyze up to 3 channels. Channels can be connected together so the difference / addition / multiplication or ratio of different channels can be analyzed. 6 alarms setting and a logic (automotive compliant) output enables stand alone operation.

Datalogging system for vertical drains

DLMU-16B is the 2nd generation data logging solution for vertical drains. This systems is expandable to include machine control and GPS systems.

Strain gauge amplifier with CAN bus

2 channel strain gauge amplifier with CAN bus interface. Convert mV inputs to CAN bus and analyze up to 2 channels. Channels can be connected together so the difference / addition / multiplication or ratio of different channels can be analyzed. 6 alarms setting and a logic (automotive compliant) output enables stand alone operation.
Go to products

GPS Sensors

A2C Sensors with integrated high performance GNSS sensor. This is the most modern solution able to track both American GPS, Russian GLONAS, European GALILEO, Chinese Beidu and Japanese Satellites. Available with integrated acceleration / tilt sensor.

Dual Hall Sensors

This sensitive dual hall sensor is perfect for sensing rotating shafts, winches, drums etc.
The A2C Brand are a category of sensors which use CAN Bus to communicate with a host. Additionally they have a logic output which can be programmed to trigger when a certain condition is met. This enables the sensor to operate without a host and act as an advanced limit switch / supervision sensor.

A2C sensors overview

Overview

The A2C Brand are a category of sensors which use CAN Bus to communicate with a host. Additionally they have a logic output which can be programmed to trigger when a certain condition is met. This enables the sensor to operate without a host and act as an advanced limit switch / supervision sensor.

A2C-TRIA2C-TRI

Measure accelerations and tilt angles (roll and pitch)

A2C-TRI-GPSA2C-TRI-GPS

Measure accelerations and tilt angles (roll and pitch). with GPS and GNSS you can time stamp, get coordinates etc. Tracking satellites from GPS, GLONAS, GALILEO, BEIDU satellites.

A2C-MAA2C-MA

Measures 3 x milliampere signals (4-20mA).

A2C-VOLTA2C-VOLT

Measures voltages (0-10V) on 3 channels.

A2C-SGA2C-SG

Connect to strain gauge or load cell. 2 channels

TOP